• White/Clear, 1ea/MD
  • White/Clear, 1ea/MD
1 2

ANI MATE

Ani Mate Dog Mate Dog Door

SKU: PT0104100215

White/Clear, 1ea/MD

$42.01 USD
$33.21 USD $42.01 USD
Sale Sold out

Dog Mate Dog Doors are suitable for a wide range of dog breeds. The medium and large doors feature robust 2-way locking panels for security. All flaps are fully brush sealed with magnetic closure for total weatherproofing and minimum energy loss from the house. Super strong, lightweight flaps are suitable for dogs small and large. Wall installation is possible using standard sheeting to line the wall. Available in medium & large sizes. Manufacturer offers a 3 year guarantee. The medium door is suitable for Spaniels, Terriers, Poodles, etc. up to 18in shoulder height.

Dimension

  • Product Gross Weight: 2.4500 lb
  • Product Net Weight: 2.4500 lb
  • Product Height: 15.25 in
  • Product Length: 11.50 in
  • Product Width: 2.00 in

Instruction

  • Battery Required: No
  • Assembly Required?: Yes
  • Assembly Instructions: 1. Remove locking panel from interior frame by simultaneously depressing the button marked 'PRESS' and lifting up. Place frame in required position where it will not be exposed to prevailing winds with tape. Note that the bottom of the aperture should be approximately level with your dogs stomach. Mark position of mounting bolt holes and draw around the aperture with a sharp pencil. Remove frame from door.2. Drill bolt holes with a 1/4 (6mm) diameter drill taking care to keep the drill square. Note that for installation in walls and doors more than 2 (50mm) thick we recommend that you attach the frames using suitable screws (not supplied) and drill holes to suit.3. Mark a cutting line 3/8 (10mm) outside the aperture and drill a hole approximately 1/4 (6mm) diameter within each corner. Cut out along the cutting line with an electric jigsaw or similar tool taking care to cut square to the door.4. Measure thickness of your door and using a sharp knife or scissors cut along the nearest guideline on the four door liners to door thickness PLUS 3/4 (19mm). Do not trim off the notch(es) on the bottom door liner. Also cut the mounting bolts supplied to your door thickness + 3/4 (19mm) using a hacksaw and file bolt ends for easy nut threading. For walls and doors greater than 2 (50mm) thick we recommend that you cut your own door liner using suitable 3/32 (2mm) metal sheet (not supplied).5. Assemble 4 door liners into the slots provided in the exterior frame and tape temporarily in position. Note that the 'notched' door liner is fitted to the bottom of the frame with the notch(es) around the frame magnet(s). The door liners should be fitted with their smooth face innermost. Push rubber seal supplied into groove in exterior frame as shown, leaving a drainage gap at bottom center.6. With the aid of a helper assemble dog door in position with tape ensuring that door liners locate properly into interior frame, then fit nuts and bolts. Do not overtighten the fixing bolts. Check flap swings freely. If it does not, check frames are undistorted and that interior frame is aligned with exterior frame. Finally, cover fixings with the plastic caps supplied and remove temporary fixing tape.7. For added security the 2 plastic pins should be inserted through the holes at the bottom of the interior frame into the locking panel.
  • Care and Cleaning Instructions: Clean using water only. Detergents and polishes may damage the plastic.

Safety

  • Caution: Plastic bags could cause suffocation, keep away from children and animals
  • Safety Warnings: Read all instructions before installing or using this product. Do not allow children to play with this product. Inspect product regularly for correct operation and damage. Do not use if in doubt. This product is designed for use with pets only, as described in these instructions. The locking system of this pet door is not intended as a security device. This pet door is not a fire resistant door and must not be used where there is a risk from fire spread. The installer of this pet door is responsible for complying with all relevant building regulations. During installation of this pet door take appropriate care. Follow safety instructions for all tools and wear appropriate personal protective equipment. Dispose of all packaging material properly.

Specifications

  • Compatible With: Wooden Door, UPVC/Metal Door, Wall
  • Locking Mechanism: Yes
  • Locking System: 2-Way
  • Opening Height: 11.75 Inches
  • Opening Width: 9.5 Inches