Skip to product information
1 of 1

EUGENE G DANNER MANUFACTURING

Danner Pondmaster Pond-Mag Magnetic Drive Water Pump

SKU: PT0172502720

Black, 1ea/950 GPH, 18Ft Cord

Regular price $137.76 USD
Regular price $109.81 USD Sale price $137.76 USD
Sale Sold out

Magnetic drive utility pumps are made to run continuously, without seals to wear out. Highly energy efficient, the savings pass on to the consumer. Suitable for large fountains, piped statuary and ponds.

Dimension

  • Product Gross Weight: 6.3500 lb
  • Product Net Weight: 6.3500 lb
  • Product Height: 5.00 in
  • Product Length: 10.80 in
  • Product Width: 7.40 in

Instruction

  • Use Instructions: Used with inline piping note the following: Centrifugal pumps cannot pull water from a lower level. In order to start, pump must be below water level and filled with water. Unless the air can escape from the outlet, the pump will not start. Do not use glues or solvents to connect the pumps threaded fittings. Use Teflon pipe tape. The pump cover is not designed to support long pipe runs or to correct pipe misalignment. To remove the base, strike with moderate force in the direction toward the pump cover. The latch will bend and the base will slide off the housing. To attach the base, slide the base (latch first) on the pump cover side of the housing. Slide the base onto the dovetail mounting tracks until the latch snaps.

Safety

  • Caution: The pump is intended to pump water only. It cannot be used to pump oil, solvents, or gasoline. Although the pump will continue to run if there is no water, after 30 minutes damage may occur if allowed to run dry.
  • Safety Listing: UL
  • Safety Warnings: a. To avoid possible electric shock, special care should be taken since water is employed in the use of aquarium equipment. For each of the following situations, do not attempt repairs by yourself; return the appliance to an authorized service facility for service or discard the appliance:1) If the appliance shows any sign of abnormal water leakage, immediately unplug it from the power source. (Immersible equipment only)2) Carefully examine the appliance after installation. It should not be plugged in if there is water on parts not intended to be wet.3) Do not operate any appliance if it has a damaged cord or plug, or if it is malfunctioning or has been dropped or damaged in any manner.4) To avoid the possibility of the appliance plug or receptacle getting wet, position aquarium stand and tank to one side of a wall-mounted receptacle to prevent water from dripping onto the receptacle or plug. A “drip loop,” shown in the figure below, should be arranged by the user for each cord connecting an aquarium appliance to a receptacle. The “drip loop” is that part of the cord below the level of the receptacle, or the connector if an extension cord is used, to prevent water traveling along the cord and coming in contact with the receptacle. If the plug or receptacle does get wet, DON’T unplug the cord. Disconnect the fuse or circuit breaker that supplies power to the appliance. Then, unplug and examine for presence of water in the receptacle.c) Close supervision is necessary when any appliance is used by or near childrend) To avoid injury, do not contact moving parts or hot parts such as heaters, reflectors, lamp bulbs, and the like.e) Always unplug an appliance from an outlet when not in use, before putting on or taking off parts, and before cleaning. Never yank cord to pull plug from outlet. Grasp the plug and pull to disconnect.f) Do not use an appliance for other than intended use. The use of attachments not recommended or sold by the appliance manufacturer may cause an unsafe condition.g) Do not install or store the appliance where it will be exposed to the weather or to temperatures below freezingh) Make sure an appliance mounted on a tank is securely installed before operating iti) Read and observe all the important notices on the appliancej) If an extension cord is necessary, a cord with a proper rating should be used. A cord rated for less amperes or watts than the appliance rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.

Specifications

  • Cord Length: 216 Inches
  • Voltage: 120 Volts
  • Wattage: 93 Watts