• Grey, 1ea
1 1

RADIO SYSTEMS CORPORATION

Drinkwell Pet Fountain 2gal

SKU: PT0137016468

Grey, 1ea

$77.88 USD
$61.91 USD $77.88 USD
Sale Sold out

The PetSafe Drinkwell 2 Gallon Pet Fountain is designed with you and your pet in mind. This automatic water bowl features a free-falling water stream with adjustable flow control. Choose from nearly silent circulation on the lowest setting to a tranquil stream on the highest. The flow control allows you to tailor the water flow to your pet's needs. The large capacity bowl is perfect for big dogs and multiple pet households and the square bowl design is large enough for several pets to drink out of at the same time with minimal splashing. When it's time to refill, simply use a pitcher to fill the bowl to the desired level. The 2 Gallon Fountain was specifically designed with no hard-to-reach crevices to clean, allowing you to spend more quality time with your pet.

Dimension

  • Dishwasher Safe: Top Rack Only
  • Product Gross Weight: 5.1500 lb
  • Product Net Weight: 5.1500 lb
  • Product Height: 14.44 in
  • Product Length: 15.75 in
  • Product Width: 5.63 in
  • Capacity: 256 oz
  • Environment: Indoor

Instruction

  • Assembly Required?: Yes
  • Assembly Instructions: 1. Rinse all fountain components (except for the adaptor) with warm water before use. This will remove any residue from the manufacturing process. Place the foam filter inside the bowl as shown.2. Place the pump inside the foam filter on the bottom of the bowl. The cord will be closest to the hole on the back of the bowl. Press down on the pump to engage the suction cups. 3. Once the pump is securely in place, feed the cord through the hole on the back of the bowl and out the notch on the bottom of the bowl.4. Remove the extra slack from the cord and push the rubber gasket firmly into the hole.5. Attach the rubber connector to the pump tube if it is not already attached. 6. Open the filter housing by using the tabs to pull it apart. 7. Rinse the carbon filter thoroughly under cold water to remove any loose carbon dust. Insert the rounded side of the carbon filter into the rounded side (Side A) of the filter housing.8. Close the filter housing by aligning the clips from the bottom and pressing down until it snaps shut.9. Insert the filter housing in to the pump tube. Attach the bottom of the filter housing to the pump tube.10. Align the bottom tab of the filter housing with the raised notch. The flat side (Side B) of the filter housing will be facing the front of the bowl.11. Attach the tower by aligning it with the raised notches on the back of the bowl.12. Insert the flow control knob into the hole on the top of the tower. Turn the knob clockwise to maximize the water stream. Turn the knob counter clockwise to decrease the water stream or shut it off.13. Attach the lid to the tower. Pick up the pet fountain by the bowl and place it in a desired location. Pour water into the bowl, leaving 1/2 inch of space between the water level and the rim of the bowl. 14. Make sure the electrical power cord, the adaptor and your hands are completely dry. Connect the in-line plug and make sure no silver is showing, then plug the adapter into a standard electrical wall outlet. NOTE: Never let the water level fall below 1 inch from the base of the bowl or your pump might fail.
  • Care and Cleaning Instructions: Pet Fountain CleaningReplace the carbon filter every 2-4 weeks and replace the foam filter every 1-2 months.1. Unplug the fountain, and disconnect the in-line plug.2. Pick up the pet fountain by the bowl, and take it to the sink.3. Pour out the water, and then disassemble the pet fountain.4. Discard the carbon filter and the foam filter. Use a solution of 80% water and 20% white vinegar to remove hard water buildup.5. Wash all other parts with warm water and soap, or place in the top rack of the dishwasher.Note: Do not place the adaptor, rubber connector or pump in the dishwasher.Pump Cleaning1. Remove the faceplate. You may need to use a fingernail to pry it off.2. Remove the yellow, teardrop-shaped stator by pulling up on the small tab.3. Use a fingernail to pull out the impeller, which is held in place magnetically. Clean the pump parts with warm water and soap, then reassemble.

Safety

  • Safety Warnings: When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and/or injury to persons, including the following:1. Read all instructions before using this product.2. To reduce the risk of injury, close supervision is necessary when an appliance is used by or near children.3. To protect against electric shock, do not place electrical power cord or plug in water or other liquids.4. Do not operate any appliance if it has a damaged electrical power cord or plug, or if it is malfunctioning or has been damaged. Call the Customer Care Center immediately for further instructions.5. To reduce the risk of electric shock, do not place or store an appliance where it can fall or be pulled into a bathtub or sink.6. Always unplug any appliance when not in use, before putting on or taking off parts and before cleaning.7. Do not use an appliance for anything other than its intended use.8. If the plug of this device gets wet, turn off the electricity to that electrical outlet. Do not attempt to unplug.9. Examine this appliance after installation. Do not plug into electrical outlet if there is water on the electrical power cord or plug.10. Do not allow pets to chew on or swallow any parts. If you are concerned your pet may chew the power cord, purchase a cord conduit (a hard plastic protector) at any hardware store.11. The plastic fountain parts are BPA-FREE. However, some animals have been known to be sensitive to plastic food and water containers. If your animal shows signs of an allergic reaction to the plastic, please discontinue use until you have consulted with your veterinarian.

Specifications

  • Cord Length: 57 Inches
  • Filter Types: Carbon
  • Voltage: 12 Volts
  • Wattage: 8 Watts