• Silver, 1ea
1 1

RADIO SYSTEMS CORPORATION

Drinkwell Stainless Steel 360 Pet Fountain 128oz

SKU: PT0117113705

Silver, 1ea

$88.63 USD
$70.50 USD $88.63 USD
Sale Sold out

Developed by a Veterinarian, the Drinkwell 360 Stainless Steel Pet Fountain provides 128 oz (1 gal) of fresh, filtered water to your pet. Multiple free-falling streams of water entice your pet to drink more and continually aerate the water with healthful oxygen. A charcoal filter removes bad tastes and odors, giving your pet the best way to stay hydrated, while the stainless steel construction makes it easy to clean and compliments any home decor! The 360's multiple streams and circular design allows pets to drink from any angle and is great for multiple pet households.

Dimension

  • Dishwasher Safe: Yes
  • Product Gross Weight: 4.2750 lb
  • Product Net Weight: 4.2750 lb
  • Product Height: 7.50 in
  • Product Length: 16.63 in
  • Product Width: 14.75 in
  • Capacity: 128 oz
  • Environment: Indoor

Instruction

  • Assembly Required?: Yes
  • Use Instructions: 1. As with any electrical device, check the electrical cord for any tears or damage before use.2. Make sure the inline plug is connected. 3. Place the pump inside the indention in the bowl. Position the pump so that the circular opening on the top, is in the upper right hand corner or true center of the bowl. Press down on the pump to engage the suction cups. Place the intake tube into the circular opening on the top of the pump.4. Align the cone so that the cord runs through the cord notch without moving the pump from its original position, Once the cord is aligned, gently place the cone piece into resting position.5. Take the partially assembled filter housing and remove the Flow Control Cap by gently lifting straight up - DO NOT TWIST TO REMOVE. Gently lift up and remove the Spout Ring to access the Filter Housing Cap.6. Unscrew Filter Housing Cap and insert the filter into the Filter Housing with the pull-tab facing up. The filter will slide easily into place. Next, screw on the Filter Housing Cap7. Look into the cone opening and make sure the intake tube is sticking straight up from the motor. Carefully, insert the Filter Housing into the cone opening and Push straight down. By pushing the Filter Housing all the way down to the rubber gasket, the housing should easily attach to the intake tube.8. Select one of the five interchangeable spouts based upon your personal preference or your pet’s. Place the chosen spout on top of Filter Housing Lid and gently press down to secure in place.9. On the Filter Housing Lid, align the Flow Control Cap with the raised notches. Press down gently and the cap will snap into place. With the Flow Control Cap, you will be able to easily adjust the intensity of the water flow. Turn the cap to the right to increase the flow of water and turn to the left to decrease. 10. Take one of the plastic cord clips and align with the electrical cord hanging over the rim of the bowl. With the two-prong end on the outside of the bowl, slide the cord clip all the way down until it clips onto the bottom of the bowl.11. Take the other two plastic cord clips and attach them to the bowl so that the three clips together form the three points of a triangle. This will lock the cone in Place. 12. Place fountain in desired location. To take care of your floors, we suggest to always use a protective mat or other durable, water resistant surface. This will help protect your floor from any water that may splash out from your pet’s use of the fountain.13. Fill the fountain bowl with water. Make sure the water level is at least to the MIN Fill Line so the pump does not run dry. This will prime the pump for use. Do not fill the fountain past the MAX Fill Line.14. Before plugging the fountain into electricity, make sure the cord and your hands are completely dry. Plug the fountain in.15. Add water as needed. Never let the water level fall lower than the MIN Fill Line (approx. 1” above the bottom of the bowl. or the pump may fail. To properly pick up the fountain, use both hands and grip underneath the sidewalls of the bowl and lift. IMPORTANT: Never pick up a full fountain by the center cone piece!
  • Care and Cleaning Instructions: Warning: When cleaning your fountain, do not use any abrasive cleaning solutions, sponges, or pads. These abrasive surfaces can scratch the stainless steel parts. The Fountain Must Be Cleaned Regularly To Continue Working Normally!FILTERS:1) Filters should be changed approximately every two weeks. Replace filters more frequently when using the fountain for multiple pets or pets that produce a lot of saliva.2) Filters are an added feature of the fountain. Their use is not required for normal operation.3) For replacement filters, visit a pet store near you or call 866-322-2530FOUNTAIN: CLEAN ONCE A WEEK1) Unplug fountain from electrical source and disconnect the inline plug.2) Remove the flow control cap and spout ring.3) Next, remove the three cord clips by gently pulling the two-prong clip up and away from the bottom of the bowl. Set the cord clips aside.4) While holding the cone steady, wrap your thumb and two fingers around the top of the filter housing and lift up to remove. If the filter housing is too tight and not moving easily, try twisting the housing back and forth in a circular motion until it loosens up enough to remove. Lift the piece up and set aside. Most likely, the intake tube will still be attached to the bottom of the filter housing5) Lift up the stainless steel cone and set aside for cleaning.6) Reach in the bowl and lift up the pump, remove and set aside for cleaning.7) While holding underneath the sidewalls of the bowl, empty the water out of the fountain.8) Clean the fountain parts with warm water and soap. You can also put the fountain in the dishwasher. IMPORTANT: do not use any abrasive cleaning solutions, sponges, or pads that could potentially scratch the stainless steel parts. Remove the pump before placing the fountain in the dishwasher. DO NOT PLACE PUMP IN DISHWASHER!9) If you have troubles reaching certain spots or hard-to-reach corners, try using a cotton swab or purchase the Drinkwell® Cleaning Kit, a 3-Piece Brush kit.PUMP MAINTENANCE:1) Remove pump from the fountain.2) Once the motor is out of the fountain, with your thumb and forefinger, gently squeeze on either side of the intake plate and pull off. It may be necessary to insert a fingernail into the seam of the intake plate to pry it off.3) Next, you will want to remove the stator by placing your finger nail under the small lip located on the narrow side of tear drop shaped stator and pull out. 4) Once the stator is removed you can also remove the impeller (3 white bladed propeller) which is held in place magnetically. To remove the impeller use a fingernail to get under the plastic blade and lift out.5) Once the motor is disassembled you can clean the parts with warm soapy water. Use a cotton swab (Q-Tip) or the Drinkwell® Cleaning Kit “Motor Brush” to get into the motor cavity and remove any build-up. For added disinfecting and hard water removal, clean the motor with a white vinegar & water solution. Strengthen the solution by increasing the amount of white vinegar used. Be sure to rinse thoroughly with fresh water.6) Once the parts are clean and dry, you can reassemble the motor for use. a) Replace the impeller. b) Replace the stator. c) Replace the intake plate.

Safety

  • Safety Warnings: 1. Read all the instructions before using appliance.2. To reduce the risk of injury, close supervision is necessary when an appliance is used near children.3. Only use attachments recommended or sold by the manufacturer.4. Do not use outdoors. FOR INDOOR USE ONLY.5. Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.6. Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or is dropped or damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair, or electrical or mechanical adjustment.7. For a portable appliance - To reduce the risk of electrical shock, do not place or store appliance where it can fall or be pulled into a tub or sink.8. Always unplug any appliance when not in use, before putting on or taking off parts, and before cleaning. Never yank a cord to remove from the outlet.

Specifications

  • Filter Types: Carbon
  • Voltage: 12 Volts
  • Wattage: 2 Watts